Polymorphic, amorphous and hydrated forms of 5-chloro-3-(4-methanesulfonyphenyl)-6'- methyl-[2,3']bipyridinyl

Form II

Form II is obtained by crystallizing compound A obtained in accordance with Preparative Example 1 from ethyl acetate.

Differential Scanning Calorimetry showed an extrapolated onset of melting at 131±1° C., and a peak melting point of 132.5±0.1° C.

Form I

Form I was obtained by recrystallizing Form II obtained as described in Example 1 from a solvent mixture of isopropanol/hexane.

Form IV

Form IV appeared spontaneously in batches of compound A prepared as in Preparative Example 1.

Form IV is alternatively prepared by contacting Form I as described in Example 2 with an organic solvent, e.g., toluene and heptane, and then recrystallizing at a temperature less than 45° C., such as about 15° C.

Form IV is also alternatively prepared by dissolving Form II in an organic solvent, such as toluene and heptane, and then recrystallizing at a temperature less than 45° C., such as about 15° C.

Form III

Form III was prepared by stirring Form IV from Example 3 in water for 1 day, and then dehydrating at 90° C. in vacuo until Form III is present. The melting temperature onset was ca. 133° C. with an enthalpy of fusion of approximately 24 kJ/mol. The peak melting temperature was 135° C.

Alternatively, using the hemihydrate of Example 5, conducting a temperature XRPD of the hemihydrate at 130° C. resulted in the production of Form III.

Hemihydrate

The hemihydrate form of compound A is produced by stirring Form IV obtained in accordance with Example 3 in water for at least 1 day. XRPD analysis of the solid produced a diffractogram identical to previous hemihydrate samples obtained for Form II. Thermogravimetry confirmed that Form IV had converted to the hemihydrate form, exhibiting a sharp weight loss of 2.45% on heating, which corresponds to a mole ratio of water to drug of 0.50%.

Sesquihydrate

The sesquihydrate of compound A is obtained by combining Form I in accordance with Example 2 and water (approximately 1.5 mol/mol compound).

Amorphous

The amorphous form of compound A is obtained by heating any polymorph to above its melting temperature (for example to 145° C.) under nitrogen, followed by quench cooling to room temperature under a dry atmosphere.

Characterization of Polymorphs

The polymorphic forms of compound A are characterized using the following procedures.

X-Ray Powder Diffraction Pattern Analysis

Polymorph I is crystalline by XRPD using a Scintag XDS-2000, Si(Li) Peltier-cooled solid state detector using a Cu K alpha source at 45 kV and 40 mA, and divergent beam (2 mm and 4 mm) and receiving beam slits (0.5 mm and 0.2 mm). Peak positions were calibrated using a standard silicon disk (97.5% pure).

Temperature XRPD studies were carried out under nitrogen, using a gold-plated copper stage with a Beryllium window on the cover. A Micristar temperature controller monitored and controlled the temperatures.

Temperature XRPD studies demonstrated that the compound did not undergo any transitions prior to melting, which was complete at 140° C., and that there was no conversion to a different polymorphic form. Similar results were obtained for Form II. The material remained amorphous and did not recrystallize.

Table 1 below lists the XRPD peak locations for Forms I, II, III and IV.

XRPD patterns for Forms I-IV are shown in FIGS. 1-4.

XRPD patterns for the two hydrate forms are shown in FIGS. 5 and 6.

Differential Scanning Calorimetry (DSC)

The extrapolated melting temperature onset of Form I was 134.0±0.6° C. with an enthalpy of fusion of 27.2±0.9 kJ/mol at 10 deg/min under nitrogen in crimped aluminum pans (FIG. 1 ). The peak melting temperature was 138° C.

When measured using a TA Instruments DSC2910 instrument, at 10° C./min under a nitrogen atmosphere in an open aluminum pan, the onset of melting was 136° C. and the peak melting temperature was as described above. There were no significant changes with DSC scanning rate other than the expected shift in peak temperature. DSC thermal behaviour of Form I in crimped sample pans under nitrogen (60 mL/min) was measured using a Seiko robotic DSC (RDC-220) at 2, 10 and 20 deg/min. The DSC was calibrated for temperature and heat flow with gallium, indium and tin.

The melting temperature onset and enthalpy of fusion of Form I were slightly higher than those observed for Form II. These polymorphic forms do not recrystallize upon cooling from the melt nor do they recrystallize on reheating. The glass transition temperature of the amorphous form (mid-point, 10K/min, crimped aluminum pan) is 55° C.

Table 2 provides a comparison of the extrapolated melting temperature onset, T o , and the enthalpy of fusion, ΔH, for Forms I, II, III and IV.

The DSC thermogram for Form IV, obtained at a scanning rate of 10° C./min under nitrogen in crimped aluminum pans, consisted of a single symmetrical endotherm with a mean onset melting point of 134.0±0.1° C. and a heat of fusion of 27.9 kJ/mol. A scanning rate of 2° C./min confirmed that the observed endotherm was due to a single endothermic transition. The enthalpy of fusion of the different polymorphs are also similar.

Forms I and IV have similar solubilities. Form IV is slightly less soluble and slightly more stable at temperatures below 45° C. Forms I and IV are enantiotropic with Form IV converting to Form I at temperatures greater than 45° C. when in contact with organic solvents.