Method for transmitting data in the access area

This application claims priority to International Application No. PCT/DE01/02584 which was published in the German language on Jan. 31, 2002.

The invention relates to a method for transmitting data in an access area.

When state of the art baseband methods are used, the range decreases with increasing transmission rate. This means that when the transmission rate is increased, the data to be transmitted can only be supplied to subscribers via trunk lines of decreasing length. If, with a predetermined distance and a selected rate, the limit is already reached, it is no longer possible to switch to an even higher rate. Since the distance to the limit is often unknown, one possibility of solving the problem is to change the rate in small steps. However, this frequently results in performance being given away. As an alternative, in principle, only those ranges can be selected at which it is ensured that they can be bridged even at the maximum possible rate.

If the transmission rate between the transmitting device and the receiving devices is to be increased, this is done such that both stations (i.e. transmitting device and receiving devices) operate at the same increased rate. For this purpose, the receiving device in question in each case must be informed by one of the stations such as, e.g. the transmitting device, that an increase in transmission rate is required and corresponding setting instructions must also be transmitted for this purpose.

The communication between transmitting device and receiving device required for this purpose takes place via a separate channel. This can be designed as an independent outband channel (user data and control data (signaling data) are conducted via different links) or inband channel (user data and control data are conducted via one link). In the latter case, care must be taken, with appropriate reliability of range, that the communication between the two stations is still ensured after switching up to a higher rate. In cases of doubt, therefore, the rate for an existing connection must be maintained.

Increasing the transmission rate above the critical limit presents problems since the level arriving at the receiving site is too low and, consequently, synchronism between the transmitting device and the receiving device is lost (“receiving device disconnecting”) and thus communication between the two stations is no longer possible. The reason for this is that in this case, the transmitting device has already adjusted itself to the increased rate but the remote station is still operating at the old rate by itself.

Communication is then no longer possible since the remote station is “disconnected”. Interworking is only possible again when both stations are manually set to the same rate.

The invention relates to a method for transmitting data in an access area.

In the access area, data are supplied to one or more subscribers (receiving devices) from a transmitting device. The transmitting device can be constructed as a multiplexer or, in the case of telephony, as a local exchange. In this arrangement, different transmission methods are applicable.

The invention discloses an approach to how synchronism between transmitting and receiving device can be reliably achieved again even after the transmission rate has been changed.

On advantage of the invention is the use of an acknowledged message exchange between the master device (local station) and the slave devices (remote stations). To this extent, characteristics of broadband technology are combined with an acknowledgement. Hence, the remote stations are not disconnected since otherwise they could no longer be reached. Due to the fact that synchronism is achieved time and again, the blocking probability of the system is reduced.

In the text which follows, the invention is explained in greater detail with reference to the exemplary embodiments shown in the FIGURE, in which:

FIG. 1 shows a local station and multiple remote stations.

FIG. 1 shows a configuration with a local station M and a plurality of remote stations S 1 . . . S n . The local station M is configured to a master device (transmitting device) and the remote stations S 1 . . . S n can act as slave devices (receiving devices). According to the invention, an acknowledged message exchange is carried out between master device M and slave devices S 1 . . . S n .

In the exemplary embodiment, it is assumed that the transmission of user data between the master device M and the slave devices S 1 . . . S n , is to be controlled at an increased transmission rate v new . This process is initiated by the master device M. Communication between the master and the slave device takes place via an inband channel. To obtain a better understanding, an increase in transmission rate between the master device M and one of the slave devices S 1 . . . S n , e.g. S 1 , is described.

Firstly, a message N is transmitted to the slave device S 1 via a management channel, by means of which message it is informed that the transmission rate v old previously used is to be increased. The message N is still transmitted at the old transmission rate v old so that the slave device S 1 can receive the message N without problems. At the same time, a timer T M is started in the master device M, on the one hand, and, on the other hand, the corresponding adjustments for increasing the transmission rate v old to the new transmission rate v new are carried out.

The message N is received and evaluated by the slave device S 1 . In response, the corresponding adjustments for increasing the transmission rate v old are carried out in the slave device S 1 . This process is acknowledged, already at the new increased transmission rate v new , by means of an acknowledgement message via the management channel to the master device M. At the same time, a timer T S is also started in the slave device S 1 .

The acknowledgement message is evaluated by the master device M and, depending on the result of the evaluation, a further acknowledgement message is supplied to the slave device S 1 . Once the slave device S 1 has received its message, it can assume that the master device M is also capable of transmitting at the new increased transmission rate v new . It is when the slave device S 1 has received this acknowledgement message at the new transmission rate v new that the transmission link for transmitting the user data at the new, increased transmission rate v new is released.

If an incorrect action takes place during these processes, the timers T M , T s ensure, after a predetermined timeout period, that both stations switch back to the old transmission rate v old . If necessary, the switchover can then be started again by the master device M.

In the exemplary embodiment, it has been assumed that the increase in transmission rate between master device M and slave device S 1 is controlled. The relevant information is deposited in the message N. However, the invention is not restricted to this type of message exchange. Thus, a multiplicity of other parameters can be exchanged. Examples of this are parameters such as clock characteristic, clock variants in master/slave, state characteristics (master/slave), synchronous/asynchronous operation or CRC check. Since the slave devices can become “disconnected” in the prior art, these parameters are often be transmitted in the correct order.

In another embodiment of the invention, the order of the parameters to be changed to the slave device is arbitrarily varied. This is a direct consequence of the invention according to which the timeout period prevents the remote station from becoming “disconnected”. It provides the possibility for automatic transmission rate detection and utilization of a maximum possible transmission rate with a predetermined line length.

In the latter case, the process begins at a low transmission rate at which it is ensured that the range can be bridged by the system. The transmission rate is then increased step by step until neither of the two acknowledgement messages can be received any more. The user data are then transmitted at the transmission rate at which the acknowledgement was still successfully carried out last.

In the case of a new installation of a connection, the transmission link can be automatically adjusted optimally with regard to transmission rate and line length. The prerequisite for this in each case is a station previously defined as master device or slave device with the lowest rate as the default setting. When autoconfiguration is activated, the master automatically then begins to change the rate once the synchronization has been established at the lowest rate.